Menu

K-FLEX ALU AA CW TAPE

High tensile strength aluminum foil, combined with cold weather solvent acrylic adhesive, protected by an easy-release silicone release paper or silicone coated blue polyethylene liner. Cold Weather version (low temperatures).

FEATURES:
> Aluminum foil provides excellent reflection of both heat and light.
> High quality adhesive with strong adhesion offers a permanent seal and bond on Foil-Scrim-Kraft Facing joints and seams in HVAC ductwork applications.
> Good resistance to aging, both indoors and outdoors.
> Low moisture vapor transmission rate offers excellent performance.

APPLICATIONS:
HVAC industry for joining and sealing Foil-Scrim-Kraft Facing laminated ductwrap / duct board joints and seams; joining and sealing flexible air duct seams and connections. General purpose holding, patching, sealing and masking applications – indoors and outdoors.

STORAGE & SHELF LIFE:
12 months when stored at 21°C (70°F) / 50% relative humidity out of direct sunlight.

SURFACE PREPARATION:
It is essential, as with all pressure-sensitive tapes, that the surface to which the tape is applied must be clean, dry, free of grease, oil or other contaminants.

PRODUCT USE:
It is essential that the user evaluate the products to determine whether it is fit for a particular purpose and user’s method of application. Good results will be obtained when applied to a clean, dry surface with a suitable pressure on products between +10 ~ +40°C (+50 ~ +105 °F).

 

 Thickness

 25 - 30 - 40 - 50 Micron

 Width

 50 - 75 - 100 mm

 Length

 50 m

K-FLEX ALU AA 130 CW
  Metric English Test method
Backing thickness 25 Micron 1.0 Mil PSTC-133 / ASTM D 3652
Total thickness 60 Micron 2.4 Mil PSTC-133 / ASTM D 3652
Adhesion to steel 15 N/25mm 54 Oz./In. PSTC-101 / ASTM D 3330
Rolling ball tack test 5 cm 2.0 In. PSTC-6 / ASTM D 3121
Tensile strength 40 N/25mm 9.1 Lb/In PSTC-131 / ASTM D 3759
Elongation 3.0 % 3.0 % PSTC-131 / ASTM D 3759
Service temperature -35 ~ +120 °C -31 ~ +248 °F  -
K-FLEX ALU AA 130 PLUS CW   
  Metric English Test method
Backing thickness 30 Micron 1.2 Mil PSTC-133 / ASTM D 3652
Total thickness 70 Micron 2.8 Mil PSTC-133 / ASTM D 3652
Adhesion to steel 15 N/25mm 54 Oz./In. PSTC-101 / ASTM D 3330
Rolling ball tack test 5 cm 2.8 In. PSTC-6 / ASTM D 3121
Tensile strength 45 N/25mm 10.2 Lb/In PSTC-131 / ASTM D 3759
Elongation 3.0 % 3.0 % PSTC-131 / ASTM D 3759
Service temperature -35 ~ +120 °C -31 ~ +248 °F  -
K-FLEX ALU AA 140 CW   
  Metric English Test method
Backing thickness 40 Micron 1.6 Mil PSTC-133 / ASTM D 3652
Total thickness 80 Micron 3.2 Mil PSTC-133 / ASTM D 3652
Adhesion to steel 15 N/25mm 54 Oz./In. PSTC-101 / ASTM D 3330
Rolling ball tack test 5 cm 2.0 In. PSTC-6 / ASTM D 3121
Tensile strength 55 N/25mm 12.5 Lb/In PSTC-131 / ASTM D 3759
Elongation 3.0 % 3.0 % PSTC-131 / ASTM D 3759
Service temperature -35 ~ +120 °C -31 ~ +248 °F  -
K-FLEX ALU AA 150 CW   
  Metric English Test method
Backing thickness 50 Micron 2.0 Mil PSTC-133 / ASTM D 3652
Total thickness 90 Micron 3.6 Mil PSTC-133 / ASTM D 3652
Adhesion to steel 15 N/25mm 54 Oz./In. PSTC-101 / ASTM D 3330
Rolling ball tack test 5 cm 2.0 In. PSTC-6 / ASTM D 3121
Tensile strength 75 N/25mm 17.0 Lb/In PSTC-131 / ASTM D 3759
Elongation 3.5 % 3.5 % PSTC-131 / ASTM D 3759
Service temperature -35 ~ +120 °C -31 ~ +248 °F  -

The physical properties of the products shown above are obtained from test methods defined by Technical Standards Authorities, Quality Assurance and Technical Service Departments and do not represent a guarantee of product performance. Individual tapes may vary from these parameters and in all applications the end user should determine whether the product is fit for a particular purpose and is suitable for the user’s method of application before use.

L’ISOLANTE K-FLEX reserves the right to change data and technical requirements without notice.
Contact us for more information.

 

back to top